Kaco blueplanet 1502xi Manuel d'utilisateur télécharger pdf (Page 32)

Page 34 blueplanet Operating and Installation Instructions 1502x - 2502x

Installation and Start-Up

5.8 Starting up the inverter

After completing the mechanical and electrical installation, the

inverter is put into operation as follows:

NOTE

The inverter can be put into operation only under daylight

conditions (i.e. at a solar generator voltage of > 100 V).

If no daylight or solar generator voltage is present, the

inverter can be activated by pressing the night start key if

there is AC voltage present (see section „Dimensions and

weights“ in the Operating Instructions). However, normal

operation is not possible in this condition. Only the values

can be read off the display.

ACTION

– Assure voltage supply

– Switch on th external AC/DC disconnect switch

(0 → 1).

During the initial start-up, the corresponding country and

language must be selected. Select the appropriate language

using the ‘2’ (right) key, press the ‘1’ (left) key to advance to

the country selection. Press the ‘2’ key to advance through the

various grid types. Once the proper grid type is selected press

the ‘1’ key then press both the ‘1’ and ‘2’ keys at the same time

to save the settings. If the improper grid settings were selected,

hold down the ‘2’ key to start the process again.

NOTE

If the power is cycled or 10 minutes elapse the settings for

the grid type are locked and a password will need to be

obtained from tech support.

The top green LED “OK” lights when DC voltage is available

and indicates that it is ready to be put into operation. The

display now indicates the current PV generator voltage “Start

from xx V, meas.: xxx V”. If the measured voltage is greater

than the starting voltage, the unit will start grid-feeding after

a country-speciﬁ c waiting time. This start-up waiting period

is required in order to ensure that the generator voltage is

continuously above the power delivery limit of 125 V (1502x)

and 200 V (2502x).

A quick start routine is provided for startup and test purposes.

This routine circumvents the start-up delay period. This quick

start routine is found in the conﬁ guration mode menu (see

Operating Instructions).

During the normal start-up procedure, the line relays audibly

switch on after a country-speciﬁ c waiting time and the feed-

ing of the grid starts. This is indicated by the middle green

LED with the house and power line symbol next to it. The

display now shows the power being fed into the grid. Key ‘1’

(left) can now be used to display the various measured values

(see„Dimensions and weights“).

5.9 Parameter programming

Various operating mode parameters can be set in the param-

eter mode menu of blueplanet units.

WARNING

Wrong parameter settings can lead to loss of

functionality as well as render your system

unsafe.

Modiﬁ cations may be made only in exceptional

cases and only after having consulted with the

manufacturer and the utility company.

Parameter menu

Country selection

Line under voltage switch-off

Line over voltage switch-off

Under frequency switch-off

Over frequency switch-off

Starting voltage 125 V (1502x) /

200 V (2502x)

Figure 27: Parameter menu

ACTION

To switch to programming mode, hold down key “2” for

approx. 20 seconds. Use key “1” to scroll through the various

menu items. The menu is continuous. When you reach the

end, the display automatically returns to the ﬁ rst item.

NOTE

After the country and grid type have been set, and either

the inverter is powered down or 10 minutes have elapsed,

and a change to the country or grid type is needed, a pass

code must be obtained from KACO support. Please have

the inverter serial number available when calling to obtain

the pass code.

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 41 42

Commentaires sur ces manuels

Pas de commentaire

Kaco blueplanet 1502xi Manuel d'utilisateur Page 32

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires photo Kaco blueplanet 1502xi